Cookies in Use
quantek shop
  ALL PRICES ARE INCLUSIVE OF VAT & ROYAL MAIL 1ST CLASS DELIVERY IN THE UK
Home Universal Garage Door Replacement Remote Control Kit Radio Remote Control Kit TELCON 500 GSM Gate ControllerGSM-AUTO GSM Remote Control Switch AllmaticAprimaticBenincaBFTCameCardaleCardinCasaliDaward Automation DEAFAACGate A Mation GeniusGibidiHormannMarantecNicePrastelQuantekRIBSEASEAVSommerSteelineTelcomaUKTX003 Ordering Contact

USEFUL LINKS
Links
   

WIRELESS RF RADIO REMOTE CONTROL KIT 868 MHz

A two channel wireless radio remote control kit operating in the 868 MHz radio frequency band.The receiver has two normally open relay contacts that can be set to operate in momentary or latching (bi-stable) mode.

The wireless RF remote control kiit comprises of 1 x two channel 868 MHz receiver and 2 x two channel 868 MHz transmitters.

Applications include the remote control of automated gates, rising barriers, garage doors, rising bollards and, Industrial RF wireless remote control.

The RF remote control kit operates on the European permitted frequency of 868.35 MHz exclusively for use by remote controls, therefore it is not subject to interference from other radio signals such as wireless headphones, walkie-talkies, wireless alarm systems, crane remote controls, wireless energy monitors and the TETRA emergency communications system.

Power supply
12V or 24V dc
Radio receiver
868.35 MHz narrow bandwidth super-hetrodyne
Operating range
Up to 100 metres
Coding method
High security rolling code anti-scan technology
Radio memory
200 codes – up to 200 transmitters can be used
Channels
2 normally open momentary or bi-stable volt free relay contacts, rating 1A 30V
Transmitter
2 channel, SAW stabalised, battery type 23A 12 volt
Dimensions
Receiver 70 x 50 x 30 mm, transmitter 50 x 30 x 10 mm

 

remote control transmitters

remote control receiver


REMOTE CONTROL KIT - £49

Including VAT & UK postage

add to cart


ADDITIONAL TRANSMITTER FOR USE WITH THE REMOTE CONTROL KIT - £17

Including VAT & UK postage

add to cart


Wireless RF Radio Remote Control Kit Manual

remote control transmitterremote control receiver

The RCKIT is a RF remote control switch and transmitters suitable for adding a remote control facility to automatic gates, barriers and garage door controllers. It requires a 12 or 24 volt dc power supply and the outputs are volt free normally open relay contacts

  1. The receiver is designed for use indoors, if used outdoors it should be housed in a suitable weatherproof enclosure
  2. Before making any connections ensure that power to the equipment you are connecting to is switched off
  3. Remove the screw securing the receiver cover and remove the cover
  4. Connect the a 12 or 24 volt dc supply, ensure positive is connected to the 12/24V terminal, If unsure use a voltmeter to locate the supply and determine the polarity, set jumper J1 to match the supply voltage
  5. The 2 transmitters supplied have been programmed if you do not have additional transmitters go to step 10,
    if you have additional transmitters program them as follows
  6. Press and release the LEARN button. The red LED on the receiver will light, and within 3 seconds
  7. Press the transmitter button A, the red LED on the receiver will flash and then turn off. The transmitter is now programmed (the transmitter button must be pressed within 3 seconds of pressing the LEARN button). Repeat the above and press button B
  8. Repeat the above for additional transmitters.
  9. Switch off power supply to the receiver
  10. Connect the output to the equipment to be controlled. Two normally open volt free relay contacts are available CH1 and CH2, each channel can be set to operate as either momentary or bi-stable, see DIP switch settings
  11. Switch on power to the receiver and test operation
  12. Replace the receiver cover
  13. Note: The single white wire is the antenna, do not cut this and for maximum range keep away from mains wiring and metallic object

Deleting learnt transmitter codes - Clearing the receiver memory
Press and keep pressed the learn button for approximately 5 seconds until the red LED on the receiver flashes and then switches off, all the transmitter codes in the memory have now been erased from the remote controls receiver.

 


nochex paypal 

 

 free uk delivery

fast delivery

 

ALL PRICES ARE INCLUSIVE OF VAT

 

 

 

Terms & Conditions | Privacy Policy | Cookies
Copyright © 2013 QUANTEK SYSTEMS LTD All Rights Reserved