Cookies in Use
quantek shop
  ALL PRICES ARE INCLUSIVE OF VAT & DELIVERY WITHIN THE UK
HomeLED EMERGENCY & NIGHT LIGHTS Automatic rechargeable power failure torch and night light 8 LED ceiling mounted automatic motion sensing light 10 LED Super Bright Automatic Wireless Motion Activated Battery Powered Night Light Universal Garage Door Replacement Remote Control Kit AllmaticAprimaticBenincaBFTCameCardaleCardinCasalDEAFAACGeniusGibidiHormanMarantecNicePrastelQuantekRIBSEASEAVSommerSteelineTelcom Ordering Contact

USEFUL LINKS
Links
   

AZAR2058 Cardale Steeline Quantek garage door remote control keyfob transmitter

Cardale and Steeline 433 MHz two button rolling code remote control transmitter for use with the Steel Line and Cardale Uni-Lift garage door openers. Cardale reference AZAR2058.

This remote control is also used with the Quantek RCS5RC and RCS6 roller shutter remote control units. Quantek reference KEYRC.

The original remote control with the green and black buttons has been replaced with the fully compatible new version shown with the two red buttons.

PCB references, green and black buttons TX3315S, two red buttons TX3316RS.

Supplied with CR23A 12 volt battery and instructions.

Please note: If your existing remote control does not resemble the ones shown in either of the pictures then this transmitter will not work with your garage door.

cardale steeline azar2058 remote control

NEW AZAR2058

quantek rcs5rc and rcs6 remote control

ORIGINAL AZAR2058

 


AZAR2058 - £23

Including VAT & UK postage

add to cart

CARDALE & STEELINE PROGRAMMING INSTRUCTIONS

The radio remote control signal is protected with a rolling code system that has many billions of combinations.
All units are supplied with a factory set Hand Transmitter coded for use with the Green button only.

Programming Additional Transmitters

CAUTION When programming additional transmitters ensure that the door is free from obstruction. When programming a transmitter the door will operate when the buttons are pressed.
We strongly recommend that the cable connecting the motor to the control box is disconnected to eliminate any chance of personal injury. The light on the control box will indicate whether or not the hand transmitter is working.

Two methods of programming can be used:-
A) Programming using an active transmitter
Push both buttons on the transmitter for approximately 5 seconds, the receiver will “bleep” indicating it is ready to learn transmitter codes, release the buttons.
Press the green button on the additional transmitter, the receiver “bleeps” to confirm it has learnt the code.(The receiver will not “bleep” if the transmitter code has already been learnt.) After about 10 seconds the receiver will “bleep” twice to indicate the learning cycle is complete.
B) Programming using the receiver.
Turn off power and carefully remove the control cover and locate the receiver box inside (Black box), then turn the power back on.
Push and release the programming button, the receiver will “bleep” indicating it is ready to learn transmitter codes.
Push the green button on the transmitter the receiver “bleeps” to confirm it has learnt the code. Wait approximately 10 Seconds, the receiver will “bleep” twice to indicate the learning cycle is complete.
Repeat this operation for as many transmitters as you require.

Erasing Memory – Deleting Learnt Transmitter Codes
Carefully remove the control cover and locate the receiver box.
Push and hold the programming button for approximately 10 seconds, three short “bleeps” will be heard confirming all the transmitter codes in the memory have been erased.

QUANTEK RCS5 and RCS6 PROGRAMMING INSTRUCTIONS

Push and release the programming button on the control panel, the receiver will ‘bleep’ indicating it is ready to learn transmitter codes.
Push the small red or black button (dependant on type of remote you have), the receiver ‘bleeps’ to confirm it has learnt the code. Repeat for all transmitters. Note: The receiver will not ‘bleep’ if the transmitter code has already been learnt.
Wait approximately 10 seconds, the receiver will ‘bleep’ twice to indicate the learning cycle is complete.
Programming is now completed and the transmitter is ready to use.

REMOTE PROGRAMMING
It is possible to program additional transmitters into the receiver, without accessing the receiver.
Using an active transmitter (one that has already been programmed into the receiver memory), push both buttons of the transmitter for approximately 5 seconds, the receiver will ‘bleep’ indicating it is ready to learn transmitter codes, release buttons.
Push the small red or black button (dependant on type of transmitter) , the receiver ‘bleeps’ to confirm it has learnt the code. Repeat for all transmitters. Note: The receiver will not ‘bleep’ if the transmitter code has already been learnt.
Wait approximately 10 seconds, the receiver will ‘bleep’ twice to indicate the learning cycle is complete.
The additional transmitter codes have now been programmed, and are ready to use.
Note: Up to 63 transmitters can be programmed.

ERASING MEMORY - DELETING LEARNT TRANSMITTER CODES
Press and keep pressed the programming button on the control panel  and wait for approximately 10 seconds, three short ‘bleeps’ will be heard confirming all the transmitter codes in memory have been erased.

 

 

 

 

 


nochex paypal

 

 free uk delivery

ALL PRICES ARE INCLUSIVE OF VAT


FEATURED PRODUCTS

motion sensing LED light

Motion Sensing Swivel Light


emergency power cut torch

Automatic Power Cut Emergency Torch


motion sensing ceiling hall light

Motion Sensing LED Hallway Ceiling Light

 

 

Terms & Conditions | Privacy Policy | Cookies
Copyright © 2016 QUANTEK TRADING LTD All Rights Reserved